Crafter's Choice™ Ribbon Column Silicone Soap Mold 2029 - Wholesale Supplies Plus
 
Current Processing Times: 1-2 Business Days
 
 
Wholesale Supplies Plus
 
   
 
 
 
Soap Molds Plastic & Silicone Molds Awareness Ribbon - (You Are Here - P11109)

Crafter's Choice™ Ribbon Column Silicone Soap Mold 2029

Pricing






Additional Information
Make ribbon shaped soaps to show your support to a cause! Embed the ribbon into a loaf to create soaps that raise awareness. Use the Teardrop Column Mold to create the middle of the ribbon (sold separately). Embed fits in Crafter's Choice Regular Loaf Silicone Mold 1501 and Rectangle Regular Column Silicone Soap Mold 2009.

Common Uses:
Melt & Pour Soap. Cold Process Soap.

Points of Interest:
Manufacturer: Crafter's Choice
Material: Silicone
Country of Origin: China

NOTE: To minimize bowing pour soap in layers.

Country Of Origin: China

Helpful Product Information:
Style: Column Avg. Bar Weight: 5.3 oz.
Bar Cavities: 1 Bar Depth: 1.5"
Bar Width: .75" Length: 8.125"
Max Pour Temperature: 135°F Max Temperature: 500ºF

This product is not on the CA Prop 65 list of toxic chemicals.

This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a).


Directions & Ingredients
International Nomenclature of Cosmetic Ingredients (INCI):
This product does need to be listed on the product ingredient label.

Common Name Ingredient Listing (FDA Approved):
This product does need to be listed on the product ingredient label.

Directions:
Melt & Pour Soap: Close the mold by firmly pressing the edges together. For added safety, clamp the edges. Slowly pour melted soap no hotter than 130ºF into mold. Allow soap to harden then open mold and remove soap. Trim edges with a potato peeler or spatula. Embed soap into a loaf or slice into bars.

Cold Process Soap: Close the mold by firmly pressing the edges together, and clamp the edges. Slowly pour traced soap into mold. After at least 24 hours, open mold and remove soap with gloved hands. Trim edges with a potato peeler or spatula. Embed soap into a loaf or slice into bars. Allow soap to cure for 4-8 weeks. Note that some cp soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.

Care:
Hand wash mold in warm, sudsy water.
SDS & Documents
Questions & Answers (4)

Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information.

Submit A Question 4 Question(s) Shown Below



Q Bubble
Posted By: Lyne   |   August 01, 2020

"What is the length and width of the Finished Ribbon soap column?"




Q Bubble
Posted By: Carol   |   September 22, 2019

"Approximately how much soap does this column hold? I am wondering because I purchased several of them and want to formulate a small recipe. Thanks much"




Q Bubble
Posted By: Linda   |   August 09, 2018

"I think the first question was how do you insert the tear drop into the ribbon. The daisy mold video shows a round middle but did not demonstrate how this was done. I'm assuming it's a two part process but how then do you insert the first embed and pour around it in the second mold? Again assuming, you'd have to hold it in place with your finger until the m&p was firm enough to release. Cute concept but pretty laborious. "




Q Bubble
Posted By: Home    |   February 05, 2017

"How do you insert the recommended teardrop insert into the mold design for use?"


Recipes & Videos (0)
CustomerReviews (1)
Submit A Rating Average Customer Rating: (1 Reviews)



Brigid • Pennsylvania

Date Submitted:  11/26/2020

"Huge disappointment "
COMMENTS:  I have been using column molds for years with my CP soap. I was so excited when I saw these... Then I used them.. They look okay in the end, but they leak like crazy, even with binder clips up both sides, they are only 8" long, which means I have to make 3 for it to fit my 18" mold, and they are almost impossible to get the soap out of without breaking. At $22 a mold (which is much more expensive than the 12" column molds I normally use), I expected much better. Total waste of $45.
PRODUCT USED IN:   Soap - Cold Process
THINGS I LIKE   THINGS I'D LIKE TO CHANGE
• Leaks
• Length
Customer Photos (0)
Charts & Calculators
 
 
Wholesale Supplies Plus LET US HELP YOU SAVINGS CENTER CONTACT US

Our Story
Contact Us
Frequently Asked Questions
Calculating Processing Times
Off-Shore Shipping Policy
Coupons
Safe Sale Guarantee
Making Bulk Purchases
1-800-359-0944
Email Us Here
Mon - Fri 8:30AM - 4:00PM EST
Sat, Sun & Holidays - Closed
We Proudly Accept:
MC-V-AMEX-Discover-PayPal
Follow Us
Careers/Job Openings

 
 

Return Policy Privacy Policy Terms & Conditions Of Sale Website User Agreement Digital Media Takedown Policy Anti-Fraud/Bullying Policy

Copyright © 2023 Wholesale Supplies Plus, LLC - All Rights Reserved